Differences

This shows you the differences between two versions of the page.

--- workshops:nvidia_jetson:xavier_nx:case_assembly [2021/02/11 12:24] – rolf
+++ workshops:nvidia_jetson:xavier_nx:case_assembly [2021/02/21 14:07] (current) – harley01
@@ Line 1: / Line 1: @@
-====== Jetson Xavier NX Case Assembly ======
+====== Jetson Xavier NX Case Assembly (without external antennas) ======
-A few days ago I (Harley Lara) received a NVIDIA Xavier NX development kit from HSRW (Prof. R. Becker) to experiment a little bit.
 The [[https://www.waveshare.com/jetson-nano-case-c.htm|metal case (C) by Waveshare]] (No. 17855) was made for a **Jetson Nano** but it can be perfectly used for a **Xavier NX** as they have the same dimensions. [[https://www.waveshare.com/wiki/Jetson_Nano_Case_(C)|The official tutorial]] to assemble the case is useful but it is necessary to make a small change because the assembly kit does not include the external antennas so it is necessary to adapt the ones included in the Xavier NX.
@@ Line 7: / Line 5: @@
 The case assembly kit contains the following items:
-{{:stud:harley01:jetson-case-c-wiki-0.png?nolink&600|}}
+{{workshops:nvidia_jetson:xavier_nx:jetson-case-c-wiki-0.png?nolink&600|}}
 Before starting, clear and clean the work area to avoid anything going wrong during the assembly process.
@@ Line 16: / Line 14: @@
 **Step 1**
-Remove the screws that hold the plate to the plastic base.
+Disconnect the antennas from the wireless network card.
-{{:stud:harley01:xavier-assemble-01.jpg?nolink&600|}}
+{{workshops:nvidia_jetson:xavier_nx:xavier-assemble-02.jpg?nolink&600|}}
 **Step 2**
-Disconnect the antennas from the wireless network card.
+Remove the screws that hold the plate to the plastic base.
-{{:stud:harley01:xavier-assemble-02.jpg?nolink&600|}}
+{{workshops:nvidia_jetson:xavier_nx:xavier-assemble-01.jpg?nolink&600|}}
 **Step 3**
 Carefully remove the antennas from the plastic base.
-{{:stud:harley01:xavier-assemble-03.jpg?nolink&600|}}
+{{workshops:nvidia_jetson:xavier_nx:xavier-assemble-03.jpg?nolink&600|}}
 **Step 4**
 Add some double-sided tape to the antennas.
-{{:stud:harley01:xavier-assemble-04.jpg?nolink&600|}}
+{{workshops:nvidia_jetson:xavier_nx:xavier-assemble-04.jpg?nolink&600|}}
 **Step 5**
 Reconnect the antennas and prepare to connect the micro-SD adapter.
-{{:stud:harley01:xavier-assemble-05.jpg?nolink&600|}}
+{{workshops:nvidia_jetson:xavier_nx:xavier-assemble-05.jpg?nolink&600|}}
 **Step 6**
 Insert the micro-SD adapter in the micro-SD port of the Xavier NX
-{{:stud:harley01:xavier-assemble-06.jpg?nolink&600|}}
+{{workshops:nvidia_jetson:xavier_nx:xavier-assemble-06.jpg?nolink&600|}}
 **Step 7**
-Put the push buttons in place.
+Put the push buttons in place, the four-wire button goes in the POWER position and the two-wire button in the RESET position.
-{{:stud:harley01:xavier-assemble-09.jpg?nolink&600|}}
+{{workshops:nvidia_jetson:xavier_nx:xavier-assemble-09.jpg?nolink&600|}}
 **Step 8**
 Put the Xavier NX inside the metal case and fix it with the M2.5 screw.
-{{:stud:harley01:xavier-assemble-07.jpg?nolink&600|}}
+{{workshops:nvidia_jetson:xavier_nx:xavier-assemble-07.jpg?nolink&600|}}
 **Step 9**
 Positioning the GPIO adapter
-{{:stud:harley01:xavier-assemble-08.jpg?nolink&600|}}
+{{workshops:nvidia_jetson:xavier_nx:xavier-assemble-08.jpg?nolink&600|}}
-{{:stud:harley01:xavier-assemble-011.jpg?nolink&600|}}
+{{workshops:nvidia_jetson:xavier_nx:xavier-assemble-011.jpg?nolink&600|}}
 **Step 10**
 Using the double-sided tape, attach the antennas to the metal case.
-{{:stud:harley01:xavier-assemble-010.jpg?nolink&600|}}
+{{workshops:nvidia_jetson:xavier_nx:xavier-assemble-010.jpg?nolink&600|}}
 **Step 11**
 Connect the flat cable between the GPIO adapter and the GPIO ports on the board.
-{{:stud:harley01:xavier-assemble-012.jpg?nolink&600|}}
+{{workshops:nvidia_jetson:xavier_nx:xavier-assemble-012.jpg?nolink&600|}}
 **Step 12**
 Screw the camera holder bottom to the case.
-{{:stud:harley01:xavier-assemble-013.jpg?nolink&600|}}
+{{workshops:nvidia_jetson:xavier_nx:xavier-assemble-013.jpg?nolink&600|}}
 **Step 13**
 To attach the camera you need 4x Screw M2x6+6, 4x screw M2x6 and 4x screw M2
-{{:stud:harley01:xavier-assemble-014.jpg?nolink&600|}}
+{{workshops:nvidia_jetson:xavier_nx:xavier-assemble-014.jpg?nolink&600|}}
-{{:stud:harley01:xavier-assemble-015.jpg?nolink&600|}}
+{{workshops:nvidia_jetson:xavier_nx:xavier-assemble-015.jpg?nolink&600|}}
-{{:stud:harley01:xavier-assemble-016.jpg?nolink&600|}}
+{{workshops:nvidia_jetson:xavier_nx:xavier-assemble-016.jpg?nolink&600|}}
 **Step 14**
 Hold the camera with 2x screw M3x6
-{{:stud:harley01:xavier-assemble-017.jpg?nolink&600|}}
+{{workshops:nvidia_jetson:xavier_nx:xavier-assemble-017.jpg?nolink&600|}}
-{{:stud:harley01:xavier-assemble-018.jpg?nolink&600|}}
+{{workshops:nvidia_jetson:xavier_nx:xavier-assemble-018.jpg?nolink&600|}}
 **Step 15**
@@ Line 87: / Line 86: @@
 **Step 16**
 Enjoy your new mini-supercomputer for AI
-{{:stud:harley01:xavier-assemble-020.jpg?nolink&600|}}
+{{workshops:nvidia_jetson:xavier_nx:xavier-assemble-020.jpg?nolink&600|}}